Stripping all the chrome. One of the single most important steps in saving money on a paint job is to strip your Mustang as much as possible yourself. This means taking off anything and everything that won't be painted. The more you take off the less the painter has to mask around. Masking not only takes their time (which costs you money) but it also results in areas that simply can't get a full coat of paint. If you take everything off, then the painters can simply scuff and spray, which will give you better and more consistent coverage. When it comes to rolling out the walls never ever use a cheap foam roller. Foam rollers never evenly absorb the paint out of the pan and will actually add time to you project and cause more mess. Buy yourself a synthetic professional 3/8 nap roller head for about $6 to $8. Not only will the paint be applied in a smoother fashion you will experience less work and mess. The second part of preparation is surface prep, it addresses covering the surfaces you do not want to get any paint on. A little plastic sheeting will go along way to keeping paint off of floors, window coverings, handrails, cabinets, counter tops, etc... And, if you are not confident with your ability to paint a straight line next to door casing, baseboards, cabinets or hardware protect these surfaces using masking tape. There are two basic types of masking tape white/yellow and blue. The white tape sticks to surfaces better but, can pull off finishes on cabinets or stained woodwork. Blue tape usually will not pull off finishes but, does not stick as well, this will probably be the tape to use for most applications. Always wipe down or dust the surface you will be masking to assure the best tape adhesion possible. If you use blue tape you may need to re-rub down the tape before painting next to it, only mask off areas with blue tape that you will be painting for a given day. With either tapes, do not assume the are a force field that paint will not penetrate, use them as a reference and dry brush the paint next to the edge of the tape and avoid soaking the edge of the tape with a lot of paint, this will cause the paint to "bleed" through giving you an undesired look. If you will need to apply multiple coats of paint, on the first coat, paint as close to the tape as you can, not really getting paint on the tape. With the second coat or a one coat application, you can use the tape more of like a paint barrier and get a little more paint on the tape if you immediately remove each section of tape after painting the section, this will keep the paint from sitting on the tape and "bleeding" behind it. Also, if you get a lot of paint on the tape it is not good to let the paint dry on the tape because some paints (especially the glossier paints) will peel if allowed to dried, with the tape when it is pulled off. White tape should not be left on for longer than a couple of days and I suggest not leaving it on more than a day in areas that receive long periods of direct sunlight. Blue tape can be left on for days, if it will stay on, there again it does not stick as well and may need rubbed down again immediately before painting up next to it.
Step three: go online and study the basics of shadow and light. It's a visual thing, and too complicated to talk about here. But once you see it, it'll come to you quickly. Simply Google "shadow and light in painting" and the basics will come up. Once you know these rules, you can apply it to any shape, any form, any painting. And it'll make you keenly aware of shadow and light on virtually any object on earth. It's what makes a painting three- dimensional and expensive looking. You can also buy art books on shadow and light at any bookstore. But make sure you sit down for a couple of hours and study it. It will come quickly to you, I promise. Now that you have primed the airless, make sure that there isn't a tip in the gun of the airless and bring it over to the empty bucket. Since there is typically cleaning solution in the hose leading to the gun it is a good idea to spray that out until you see thick paint coming out. Once you have thick paint coming out you may put your tip back in. Remember that the tip will have an arrow on one side of the handle that shows which direction it must be in, in order to spray. Technical advancements are constantly being made to improve the life span, durability, wear and performance of exterior paints. The Akrylatfarg range at Ray Munn, for example, is an environmentally sound water-based option. A flat, semi-gloss, or high-gloss finish may be applied to the primed surface. For a flat finish, two coats of flat wall paint should follow the priming coat. For a semi-gloss finish, one coat of flat wall paint and one coat of semi-gloss paint should be applied to the primed surface. For a high-gloss finish, one coat of semi-gloss paint and one coat of high-gloss enamel should be used over the priming coat.