If you have a vinyl top then remove the molding separating the vinyl and paint. Drip rail chrome really should be removed also, but can be extremely hard to take off undamaged. If you plan on buying all new drip molding then definitely remove the old for painting. But if you want to keep the originals then it might be better to leave them on and let the painter mask around. If you have hub caps it's easy to just take them off. While the paint shop should completely mask all four tires, overspray can still find its way in. It's sometimes better to play it safe and just remove wheel covers. Paints in powdered form require the addition of a liquid to prepare them for use. The manufacturer's directions as to the amount of oil, varnish, water, or other vehicle required should be followed. Note: How to use an airless paint sprayer. I'm sure the guy at the rental store showed you how to use the airless (typically with his limited experience of actually painting a house), so hopefully I can offer you a couple new ideas on how to paint your home using an airless paint sprayer. When you first get the airless home, set it in the middle of the area that you would like to start painting. Typically the length of the hose is around 50'. Stretch out the hose prior to painting so that you don't have to worry about unraveling it while you are painting on a ladder. It is a good idea to have a 100' extension cord so that you can bring the airless anywhere you wish to paint without any restrictions. Tip: before you plug in the airless into the extension cord, MAKE SURE THE AIRLESS IS OFF! You don't want the airless to start pumping without paint! Now, when you go to set up the airless, before you turn it on, it's a good rule of thumb to have a second empty bucket next to your bucket of paint. I'll explain why in a second. Place both buckets side by side and place the intake hose (with the wire mesh filter end) into your 5 gallon bucket of paint while the primer hose (usually a lot smaller, about the size of a pencil'ish) is placed in the empty bucket of paint. Before you turn on the machine make sure that the airless is set to prime the machine first. There is a primer valve that you can rotate between prime and paint. A good way to see if the valve is set to prime or paint is to try this little test prior to turning the machine on. While turning the valve clockwise a couple times you will notice that the valve handle will separate from the machine in one position (leaving a slight crack between the valve and machine) while the other position the valve is close to the machine. The position in which the valve is separated from the machine is considered the primer position. Do this multiple times to see what I'm talking about. Don't worry if you keep on spinning the valve, you can spin it a million times in one direction and it won't hurt it.
Limewash - Made from slaked lime and water, this paint is good for porous surfaces such as brickwork, render and plaster and gives a chalky finish. It is available from specialist companies. Acrylic is the second new name for magic in paints. This is also a plastic-in-water. Solid acrylic you know as the beautiful, glasslike Plexiglas and Lucite. Proper brush technique: When "cutting in" with a paint brush you should dip the brush in paint and tap the sides of the bucket on each side of the brush, leaving a good amount on the brush so you are able to minimize the times you will need to dip/load the brush. Next, take the brush and make a one foot to two foot line down the wall about an inch or two away from the trim or surface you are going to paint up next to, this is much like taking a knife full of butter and spreading it across an entire slice of bread. After, spreading the paint over the section, go back and even the paint out evenly across the section and cut up next to the trim with the brush. You want to paint up next to the trim or surfaced to be cut-in with the paint brush after you have released most of the paint on the wall, it is easier to cut in with the tips of the brush exposed and not loaded with a lot of paint. The most flattering eye shadows are green blue, blue grays and lavender. The best eye pencils colors are in medium blues and charcoal. Lipstick and blush colors should be in rose, pink or plum colors. Let you lashes appear longer and fuller with navy or charcoal mascara.