The Carolina Panthers are a professional American football team based in Charlotte, North Carolina. The Panthers compete in the National Football League (NFL), as a member club of the league’s National Football Conference (NFC) South division. The team is headquartered in Bank of America Stadium in uptown Charlotte; the stadium also serves as the team’s home field. They are one of the few NFL teams to own the stadium they play in, which is legally registered as Panthers Stadium, LLC. The Panthers are supported throughout the Carolinas; although the team has played its home games in Charlotte since 1996, it played home games at Memorial Stadium in Clemson, South Carolina during its first season. The team hosts its annual training camp at Wofford College in Spartanburg, South Carolina.
You'll need a large compressor, not just the typical 20 gallon variety most of us have. This is a 60 gallon, vertical compressor with typically a 5+ hp motor. Then you'll need a decent paint gun (possibly 2; one for primer and one for color) which again is an expense. Then there's the question of where you'll paint the car. Renting a paint booth is best, but can be expensive and hard to find. You can always seal up your garage or shoot out in the wetted down driveway, but you'll inevitably get dirt and moisture into the paint. STENCILING. You may want designs on the walls, or perhaps even on floors and ceilings, in some of the rooms or hallway. You may buy or make your own stencils, which should be on heavy paper, stencil board, plastic, or metal. Avoid stencils made of lightweight paper which will get soaked when touched by wet paint. Your paint dealer will suggest the best paint for you to use, as it will depend a great deal on the surface over which you want to put the stenciled designs. Generally a heavy paint is used, so that it will not spread under the stencil while you are applying it. The second part of preparation is surface prep, it addresses covering the surfaces you do not want to get any paint on. A little plastic sheeting will go along way to keeping paint off of floors, window coverings, handrails, cabinets, counter tops, etc... And, if you are not confident with your ability to paint a straight line next to door casing, baseboards, cabinets or hardware protect these surfaces using masking tape. There are two basic types of masking tape white/yellow and blue. The white tape sticks to surfaces better but, can pull off finishes on cabinets or stained woodwork. Blue tape usually will not pull off finishes but, does not stick as well, this will probably be the tape to use for most applications. Always wipe down or dust the surface you will be masking to assure the best tape adhesion possible. If you use blue tape you may need to re-rub down the tape before painting next to it, only mask off areas with blue tape that you will be painting for a given day. With either tapes, do not assume the are a force field that paint will not penetrate, use them as a reference and dry brush the paint next to the edge of the tape and avoid soaking the edge of the tape with a lot of paint, this will cause the paint to "bleed" through giving you an undesired look. If you will need to apply multiple coats of paint, on the first coat, paint as close to the tape as you can, not really getting paint on the tape. With the second coat or a one coat application, you can use the tape more of like a paint barrier and get a little more paint on the tape if you immediately remove each section of tape after painting the section, this will keep the paint from sitting on the tape and "bleeding" behind it. Also, if you get a lot of paint on the tape it is not good to let the paint dry on the tape because some paints (especially the glossier paints) will peel if allowed to dried, with the tape when it is pulled off. White tape should not be left on for longer than a couple of days and I suggest not leaving it on more than a day in areas that receive long periods of direct sunlight. Blue tape can be left on for days, if it will stay on, there again it does not stick as well and may need rubbed down again immediately before painting up next to it.
Once the drywall compound/spackle has had sufficient time to dry, you will need to lightly sand the surface of the repair to smooth out any ridges that may have been caused while "coating" the patch. Once you have the surface sanded smooth, take a wet sponge or cloth and, by lightly washing/rubbing, blend the outside edge of the drywall compound/spackle back into the wall. For a smaller repair, you can wash away the excess drywall compound, leaving only the compound/spackle only in the area where the indent was filled. For a larger hole, after filling, sanding and using a wet sponge to blend the outside edge of the compound back into the wall, it may be necessary to texture the area in order to give the smooth patch the appearance of the existing wall. Today, it is increasingly easy to source ecologically sound paints, as most specialist ranges, such as Ecos, Earthborn, Georgina Barrow and Auro are available via mail order. There is a wealth of colour options in these pre-mixed ranges that include lush shades and muted palettes, reflecting their natural ingredients. Ecos continues to lead the field. It has recently developed Atmosphere Purifying Paint, which absorbs and neutralises volatile chemicals, solvents and VOCs from the atmosphere in a home. The area covered by a gallon of whitewash depends upon the nature of the surface, but ordinarily a gallon will cover about 225 sq. ft. on wood, about 180 sq. ft. on brick, and about 270 sq. ft. on plaster. The formulas mentioned will make from 10 to 14 gallons of whitewash. If a smaller quantity is desired, the amount of each ingredient should be reduced proportionately. After the siding of your home is painted you can now start on painting the trim. There are a couple different ways you can go about painting the trim of your house. The first way is to mask off all of the trim so that you can merely spray the trim color on to your house, and the second way is to roll the trim by hand. If you are the only person painting the house I would recommend rolling the trim by hand. The reason being is because it takes a long time to mask off all of the trim on your home compared to just rolling the face of the trim boards. If you have multiple people, it would be faster to have the helpers mask everything off while you start spraying the trim color.